ASTM D – 11, “Standard Test Methods for Field Measurement of Surface locations and the arithmetic mean determined, Method C—A composite plastic. Designation: D – 03Standard Test Methods for Field Measurement of 3 Method C—A composite plastic tape is impressed into Method C—A These test methods are under the jurisdiction of ASTM Committee D01 on The sole. ASTM D – 11 Standard Test Methods for Field Measurement of Surface Profile 1 of 8 standard.3 Method C—A special tape3 containing a compressible 6.
|Published (Last):||25 July 2010|
|PDF File Size:||10.84 Mb|
|ePub File Size:||1.36 Mb|
|Price:||Free* [*Free Regsitration Required]|
Therefore, differences are inevitable, particularly with deeper surface profiles, and the results may or may not fall within the specified range for one of the two methods. ASTM D contains three methods of measuring surface profile depth: Both the structure and the coating system protecting the structure will move while in service.
This can be discussed and agreed upon at aatm pre-construction conference. The creation of this peak-valley pattern in the surface effectively increases the surface area, providing astm d4417 method c anchor for the coating system.
Differences in Surface Profile Measurements: ASTM D4417- Method B vs. Method C
As acknowledged in Dscoring methox cause micro-cracking in the coating, which may cause diminished pull-off strengths. So, in effect the reading on the micrometer or the RTR from the replica tape represents several peaks and valleys, while the depth micrometer does not. Historical Version s – view previous versions astm d4417 method c standard. Early detection and removal of appreciable amounts of surface chloride contamination prior to coating installation can prolong the service life of a coating, reducing the frequency of maintenance painting and reducing life cycle costs.
Same Surface, Different Results? As a result, there are differences in testing procedures that should asgm considered when evaluating astm d4417 method c applied to astm d4417 method c, versus coatings applied to steel. For Method C, there are various ranges of replica tape that can be employed. However, thick film coatings i. Data published in Appendix X1 of the standard generated by an earlier interlaboratory research initiative reveals different pull-off strengths on four test specimens when using the various adhesion testers at that time, only four of the five testers that are in the current standard were included in the research.
Many astm d4417 method c manufacturers have developed loading fixtures with a larger surface area i. Link to Active This link will always route to the current Active version of the standard. Coating manufacturers may also consider these requirements to improve the performance and the service life of the coatings they supply.
Industrial Protective Coatings
Standards for Measurement of Surface Profile There are currently four primary standards for measurement of surface profile in steel surfaces. This is done because of evidence that coatings performance in any one small area is primarily influenced by the highest surface features in that area and not by the average roughness.
The method describes three different procedures for quantifying surface profile, including visual comparators Method Adepth micrometers Method B and replica tape Method C. Industrial Astm d4417 method c Coatings by William D.
Today, Method B and Method C are the most commonly used, so that is what we will be focusing on. Methods of generating various peak densities astm d4417 method c aastm in the articles, and are based on abrasive size, shape, hardness and other factors.
Method B depth micrometer incorporates a special spring-tension micrometer with a 1-inch 2. With the base of the micrometer resting on the peaks of the surface profile, and the conical pin protruding to a valley of astm d4417 method c profile, the distance is read from the gage display in mils or micrometers. Profile depth designations are based on the concept of mean maximum profile h max ; this astm d4417 method c is determined by averaging a given number usually 20 of the highest peak to lowest valley measurements made in the field of view of a standard measuring microscope.
The subcommittee develops and maintains standard test methods, practices and guides relating to the performance, evaluation, specification, application and proper use of industrial protective coatings.
Surface profile is defined as a measurement astm d4417 method c mdthod maximum peak-to-valley depth created by abrasive impingement against a surface during abrasive blast cleaning operations, or by an impact-type power tool. Standards for Measurement of Surface Profile. Elevated aastm of chloride can also lead to section loss and pitting of the steel substrate, as chloride contamination can accelerate the corrosion process.
When the abrasive impacts the surface, it cuts into the surface angular abrasives or peens e4417 surface round abrasives and creates a series of peaks and valleys in the surface. This method can be used to measure the surface profile depth that is created aztm abrasive blast cleaning or impact-type power tools.
This includes personalizing content and advertising. Specify the Test Instrument! Through the efforts of Subcommittee D The pattern of surface roughness is replicated by burnishing the tape, effectively pressing the compressible mehod into the surface roughness. Peak density the number of peaks per unit area also plays a key role in maintaining adhesion of the metyod system astm d4417 method c provides greater resistance to corrosion undercutting when the coating system xstm damaged while in service.
Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. See Figures 1314 ICS Number Code Some of the coatings are applied up to 3. The values given in parentheses are for astm d4417 method c only. Soluble salts like chloride, when trapped beneath a newly applied coating, can draw water through the coating film by a process methox as osmosis and cause blistering and underfilm corrosion.
How is Surface Profile Depth Quantified? V4417 example, requiring a 5. Further, the tensile strength of steel far exceeds the tensile strength of an industrial protective coating.
The base of the instrument rests on the peaks of the surface astm d4417 method c while the d point projects into the valley. To avoid these discrepancies, it is recommended that a single method be employed on a project. In response to a growing demand, a number of coatings were developed and advertised as being resistant to graffiti, or easily cleaned of graffiti.
The ast method is widely used by coatings manufacturers, specifiers, inspectors astm d4417 method c coating specialists. The four standards are: Historical Version s – view previous versions of standard Work Item s – proposed revisions of this standard Translated Version s: There are currently four primary standards for measurement of surface profile in steel surfaces.